Skip to main content

Canon EOS 3D DSLR Miniature - 16GB camera Pen Drive





Canon EOS 3D DSLR camera miniature, best quace slr camera shaped cool fancy usb flash 16gb pen drive only Rs.475 on Amazon.

Canon SLR Camera Shaped Pen Drive - https://amzn.to/33Fb8Yw
Sony SLR Camera Shaped Pen Drive - https://amzn.to/32ro6IU
Iron Man Silver Metal Face with LED Pen Drive - https://amzn.to/2BiwezB
Bottle Pen Dribe - https://amzn.to/32mLcjT
F1 Racing Car USB Pen Drive - https://amzn.to/2VNhQJ0
Robot Pen Drive - https://amzn.to/2BvINrD



Comments

Popular posts from this blog

Clap On Off Switch Circuit Using Arduino

  Arduino Clap LED program #define MicAO 8 int ledPin = 13; int clap = 0; long detection_range_start = 0; long detection_range = 0; boolean status_lights = false; void setup() {   pinMode(MicAO, INPUT);   pinMode(ledPin,OUTPUT);   } void loop() { int status_MicAO = digitalRead(MicAO); if (status_MicAO == 0) { if (clap == 0) { detection_range_start = detection_range = millis(); clap++; } else if (clap > 0 && millis()-detection_range >= 50) { detection_range = millis(); clap++; } } if (millis()-detection_range_start >= 400) { if (clap == 2) { if (!status_lights) { status_lights = true; digitalWrite(ledPin, HIGH); } else if (status_lights) { status_lights = false; digitalWrite(ledPin, LOW); } } clap = 0; } }

IOT Based Water Level Indicator Project Using Esp32 And Ultrasonic Sensor

  Water Level Indicator Project Using ESP32   Water Level Indicator with Alarm on Tank Full.   IoT Wi-Fi smart water level indicator for tanks with mobile app control . 📟 OLED Display (0.96" I2C SSD1306)   OLED Pin         ESP32 Pin VCC                     3.3V GND                     GND SDA                    GPIO 21 SCL                      GPIO 22     🔔 BUZZER   Buzzer Pin        ESP32 Pin   +           GPIO 26 -            GND         Each LED connects to an ESP32 GPIO pin via a current-limiting resistor.   ...

DIY ORTOMI ROBOT FACE USING ESP32 CONNECTION DIAGRAM

  0.96” I2C   28x64 SSD1306 OLED Display Wiring :- VCC – 3.3V GND – GND SCL(OLED) – GPIO 22 ( ESP32 ) SDA(OLED) – GPIO 21 ( ESP32 )   TTP223 Touch Sensor Wiring :- VCC – 3.3V {Add 10R resistor with this pin} (ESP32) GND – GND (ESP32) I / O   – GPIO 14 (ESP32)   Speaker OR Buzzer :-   + POSITIVE –   GPIO 25 (ESP32) - NEGETIVE - GND (ESP32)   Required Libraries to Install:- Adafruit_GFX Adafruit_SSD1306 Wire     Note:- Download Emotions.h and SoundFX.h file for link below and paste in same folder where code.uno file save.     Full Code:- RobotFace.ino #include <Wire.h> #include <Adafruit_GFX.h> #include <Adafruit_SSD1306.h> //#include "Emotions.h" #include "Emotions_CLEAN.h" #include "SoundFX.h"   #define SCREEN_WIDTH 128 #define SCREEN_HEIGHT 64 #define OLED_RESET     -1 Adafruit_SSD1306 display(SCREEN_WIDTH, SCREEN_H...