Skip to main content

How To Make Led Flasher Using BC547 Transistor


How to make led flasher using BC547 transistor for bike ,car, RC car etc. Very simple 12v flasher circuit.

Need For This Project ,-

LED :- https://amzn.to/3lwOH3F

Piezo Buzzer :- https://amzn.to/3xqeNIa

1k resistor :- https://amzn.to/3lAWe1E

100 ohm registor :- https://amzn.to/3iqbJHN

1000uf 16v capacitor :- https://amzn.to/3ipW230

BC 547 transistor :- https://amzn.to/37ktWA7

Combo Pack :- https://amzn.to/2Vv3cKJ


Labels:

Comments

Post a Comment

Popular posts from this blog

Clap On Off Switch Circuit Using Arduino

  Arduino Clap LED program #define MicAO 8 int ledPin = 13; int clap = 0; long detection_range_start = 0; long detection_range = 0; boolean status_lights = false; void setup() {   pinMode(MicAO, INPUT);   pinMode(ledPin,OUTPUT);   } void loop() { int status_MicAO = digitalRead(MicAO); if (status_MicAO == 0) { if (clap == 0) { detection_range_start = detection_range = millis(); clap++; } else if (clap > 0 && millis()-detection_range >= 50) { detection_range = millis(); clap++; } } if (millis()-detection_range_start >= 400) { if (clap == 2) { if (!status_lights) { status_lights = true; digitalWrite(ledPin, HIGH); } else if (status_lights) { status_lights = false; digitalWrite(ledPin, LOW); } } clap = 0; } }
Post a Comment
Read more

IOT Based Water Level Indicator Project Using Esp32 And Ultrasonic Sensor

  Water Level Indicator Project Using ESP32   Water Level Indicator with Alarm on Tank Full.   IoT Wi-Fi smart water level indicator for tanks with mobile app control . 📟 OLED Display (0.96" I2C SSD1306)   OLED Pin         ESP32 Pin VCC                     3.3V GND                     GND SDA                    GPIO 21 SCL                      GPIO 22     🔔 BUZZER   Buzzer Pin        ESP32 Pin   +           GPIO 26 -            GND         Each LED connects to an ESP32 GPIO pin via a current-limiting resistor.   ...
Post a Comment
Read more

DIY ORTOMI ROBOT FACE USING ESP32 CONNECTION DIAGRAM

  0.96” I2C   28x64 SSD1306 OLED Display Wiring :- VCC – 3.3V GND – GND SCL(OLED) – GPIO 22 ( ESP32 ) SDA(OLED) – GPIO 21 ( ESP32 )   TTP223 Touch Sensor Wiring :- VCC – 3.3V {Add 10R resistor with this pin} (ESP32) GND – GND (ESP32) I / O   – GPIO 14 (ESP32)   Speaker OR Buzzer :-   + POSITIVE –   GPIO 25 (ESP32) - NEGETIVE - GND (ESP32)   Required Libraries to Install:- Adafruit_GFX Adafruit_SSD1306 Wire     Note:- Download Emotions.h and SoundFX.h file for link below and paste in same folder where code.uno file save.     Full Code:- RobotFace.ino #include <Wire.h> #include <Adafruit_GFX.h> #include <Adafruit_SSD1306.h> //#include "Emotions.h" #include "Emotions_CLEAN.h" #include "SoundFX.h"   #define SCREEN_WIDTH 128 #define SCREEN_HEIGHT 64 #define OLED_RESET     -1 Adafruit_SSD1306 display(SCREEN_WIDTH, SCREEN_H...
Post a Comment
Read more