Skip to main content

VOTO V2i Mobile Unboxing and Review





screen size: 5.5 inches (13.97 cm)
screen resolution: Full HD (1080 x 1920 pixels)
SIM Slot(s)‎: ‎Dual SIM (Nano), GSM+GSM
Operating System: Android v6.0 (Marshmallow)
Performance: Octa core, 1.3 GHz
Display: 5.5" (13.97 cm)
Storage: 32 GB
Camera: 13 MP 5MP
Battery: 3500 mAh
Ram: 3 GB
Fingerprint Sensor: Yes (Rear Position)
Other Sensors: Light sensor, Proximity sensor, Accelerometer
Network:4G

Labels:

Comments

Post a Comment

Popular posts from this blog

Clap On Off Switch Circuit Using Arduino

  Arduino Clap LED program #define MicAO 8 int ledPin = 13; int clap = 0; long detection_range_start = 0; long detection_range = 0; boolean status_lights = false; void setup() {   pinMode(MicAO, INPUT);   pinMode(ledPin,OUTPUT);   } void loop() { int status_MicAO = digitalRead(MicAO); if (status_MicAO == 0) { if (clap == 0) { detection_range_start = detection_range = millis(); clap++; } else if (clap > 0 && millis()-detection_range >= 50) { detection_range = millis(); clap++; } } if (millis()-detection_range_start >= 400) { if (clap == 2) { if (!status_lights) { status_lights = true; digitalWrite(ledPin, HIGH); } else if (status_lights) { status_lights = false; digitalWrite(ledPin, LOW); } } clap = 0; } }
Post a Comment
Read more

IOT Based Water Level Indicator Project Using Esp32 And Ultrasonic Sensor

  Water Level Indicator Project Using ESP32   Water Level Indicator with Alarm on Tank Full.   IoT Wi-Fi smart water level indicator for tanks with mobile app control . 📟 OLED Display (0.96" I2C SSD1306)   OLED Pin         ESP32 Pin VCC                     3.3V GND                     GND SDA                    GPIO 21 SCL                      GPIO 22     🔔 BUZZER   Buzzer Pin        ESP32 Pin   +           GPIO 26 -            GND         Each LED connects to an ESP32 GPIO pin via a current-limiting resistor.   ...
Post a Comment
Read more

DIY ORTOMI ROBOT FACE USING ESP32 CONNECTION DIAGRAM

  0.96” I2C   28x64 SSD1306 OLED Display Wiring :- VCC – 3.3V GND – GND SCL(OLED) – GPIO 22 ( ESP32 ) SDA(OLED) – GPIO 21 ( ESP32 )   TTP223 Touch Sensor Wiring :- VCC – 3.3V {Add 10R resistor with this pin} (ESP32) GND – GND (ESP32) I / O   – GPIO 14 (ESP32)   Speaker OR Buzzer :-   + POSITIVE –   GPIO 25 (ESP32) - NEGETIVE - GND (ESP32)   Required Libraries to Install:- Adafruit_GFX Adafruit_SSD1306 Wire     Note:- Download Emotions.h and SoundFX.h file for link below and paste in same folder where code.uno file save.     Full Code:- RobotFace.ino #include <Wire.h> #include <Adafruit_GFX.h> #include <Adafruit_SSD1306.h> //#include "Emotions.h" #include "Emotions_CLEAN.h" #include "SoundFX.h"   #define SCREEN_WIDTH 128 #define SCREEN_HEIGHT 64 #define OLED_RESET     -1 Adafruit_SSD1306 display(SCREEN_WIDTH, SCREEN_H...
Post a Comment
Read more