10 Best Power Bank 2017 India Under 2000

Here I give you list of 10 best power bank in 2017 in India under Rs. 2000 and their price and specifications.

You Can Buy it From here:-

1. PNY BE-740 -------------- http://amzn.to/2guywku
2. Romoss 10000 mAh Power Bank -------------- http://amzn.to/2eSkvNA
3. ADATA PT100 ---------- http://amzn.to/2evC45i
4. PNY BE-520 ---------- http://amzn.to/2eveghP
5. Asus 10050mAH Zen ------------ http://amzn.to/2x2QiGe
6. Lenovo Power Bank --------- http://amzn.to/2eA3pqL
7. Easy ACC -------- http://amzn.to/2ezWpdh
8. Ambrane P-1310 Power Bank -------- http://amzn.to/2vCwJUW
9. Intex IT-PB11K -------- http://amzn.to/2evevcJ
10. TP-Link TL-PB10400 --------- http://amzn.to/2x2hXXC

Comments

Clap On Off Switch Circuit Using Arduino

Arduino Clap LED program #define MicAO 8 int ledPin = 13; int clap = 0; long detection_range_start = 0; long detection_range = 0; boolean status_lights = false; void setup() { pinMode(MicAO, INPUT); pinMode(ledPin,OUTPUT); } void loop() { int status_MicAO = digitalRead(MicAO); if (status_MicAO == 0) { if (clap == 0) { detection_range_start = detection_range = millis(); clap++; } else if (clap > 0 && millis()-detection_range >= 50) { detection_range = millis(); clap++; } } if (millis()-detection_range_start >= 400) { if (clap == 2) { if (!status_lights) { status_lights = true; digitalWrite(ledPin, HIGH); } else if (status_lights) { status_lights = false; digitalWrite(ledPin, LOW); } } clap = 0; } }

IOT Based Water Level Indicator Project Using Esp32 And Ultrasonic Sensor

Water Level Indicator Project Using ESP32 Water Level Indicator with Alarm on Tank Full. IoT Wi-Fi smart water level indicator for tanks with mobile app control . 📟 OLED Display (0.96" I2C SSD1306) OLED Pin ESP32 Pin VCC 3.3V GND GND SDA GPIO 21 SCL GPIO 22 🔔 BUZZER Buzzer Pin ESP32 Pin + GPIO 26 - GND Each LED connects to an ESP32 GPIO pin via a current-limiting resistor. ...

DIY ORTOMI ROBOT FACE USING ESP32 CONNECTION DIAGRAM

0.96” I2C 28x64 SSD1306 OLED Display Wiring :- VCC – 3.3V GND – GND SCL(OLED) – GPIO 22 ( ESP32 ) SDA(OLED) – GPIO 21 ( ESP32 ) TTP223 Touch Sensor Wiring :- VCC – 3.3V {Add 10R resistor with this pin} (ESP32) GND – GND (ESP32) I / O – GPIO 14 (ESP32) Speaker OR Buzzer :- + POSITIVE – GPIO 25 (ESP32) - NEGETIVE - GND (ESP32) Required Libraries to Install:- Adafruit_GFX Adafruit_SSD1306 Wire Note:- Download Emotions.h and SoundFX.h file for link below and paste in same folder where code.uno file save. Full Code:- RobotFace.ino #include <Wire.h> #include <Adafruit_GFX.h> #include <Adafruit_SSD1306.h> //#include "Emotions.h" #include "Emotions_CLEAN.h" #include "SoundFX.h" #define SCREEN_WIDTH 128 #define SCREEN_HEIGHT 64 #define OLED_RESET -1 Adafruit_SSD1306 display(SCREEN_WIDTH, SCREEN_H...

Just For You

Search This Blog